-
1 интенсивность пластической деформации
Русско-английский политехнический словарь > интенсивность пластической деформации
-
2 скорость пластической деформации
Русско-английский политехнический словарь > скорость пластической деформации
-
3 интенсивность пластической деформации
Engineering: plastic strain rate, plastic-strain rateУниверсальный русско-английский словарь > интенсивность пластической деформации
-
4 скорость пластической деформации
Engineering: plastic strain rateУниверсальный русско-английский словарь > скорость пластической деформации
-
5 упругопластическая деформация
напряжение при срезе; деформация сдвига — shearing strain
сжимающее усилие; деформация сжатия — compression strain
Русско-английский военно-политический словарь > упругопластическая деформация
-
6 потеря устойчивости при малой скорости деформации
внутренняя деформация — internal strain; internal flow
напряжение, вызывающее пластическую деформацию — flow stress
Авиация и космонавтика. Русско-английский словарь > потеря устойчивости при малой скорости деформации
-
7 для учёта
•The analysis must he modified to accommodate the fact that...
•Formulas were developed to account for the effect of external pressure.
•To correct for the effect of pressure drop on gas velocity...
•A simple modification is necessary to take account of non-equilibrium conditions.
•To take into account (or To allow for) magnetic deflection...
•Corrections should be made to account for the distortion of...
* * *Для учёта -- to accommodate, to account for, to allow for, to take account of, to take into accountThese modifications had been found to be necessary to accommodate the nonuniform plastic flow of the workpiece.To account for this fact, a surface hardness measurement at a high strain rate is required.No correction was applied to take account of the effects of turbulence.Under these conditions the stalled flow model would have to be modified to take this pressure drop into account.Русско-английский научно-технический словарь переводчика > для учёта
-
8 уменьшаться
Уменьшаться - to decrease, to drop, to fall, to fall off, to lessen, to decline, to relax, to decay; to be decreased, to be reduced, to be diminishedWe see that as firing rate is reduced, M, which is the mass of the combustion gases, decreases linearly.Then the pressure begins to drop as the flow redevelops and continues to drop due to friction in the fully developed regime.As energy is dissipated locally, the temperature rises, the local moduli fall, and the specimen stiffness and damping are reduced.In either case both the tube load and bending stress fall off fairly rapidly away from the outer edge of the tubesheet.We observed in the blunt notched-specimen simulations that the plastic-strain field lessens 63 percent over a distance that is comparable to the 0.25-mm notch-root radius.The effectiveness is shown to decline with increasing cant angle.Following the air flow disturbance, both model results and test data show an initial overshoot (перерегулирование) in steam pressure which then relaxes to a lower value.On the latter bar, the extent of surface damage is significantly reduced due to the inhibiting of the surface/environment interaction by the relatively inert environment.Уменьшаться на-- The first critical speed and the onset speed of instability drop by approximately 7 and 6 percent, respectively.Русско-английский научно-технический словарь переводчика > уменьшаться
-
9 удлинение
1. lengthening; extensionудлинение; растягивающее усилие — extension strain
местное удлинение; местное расширение — local extension
2. elongationРусско-английский словарь по информационным технологиям > удлинение
См. также в других словарях:
Dynamic strain aging — Although sometimes dynamic strain aging is used interchangeably with the Portevin–Le Chatelier effect (or serrated yielding), dynamic strain aging refers specifically to the microscopic mechanism that induces the Portevin–Le Chatelier effect.… … Wikipedia
The Andromeda Strain (2008 miniseries) — Infobox Film name = The Andromeda Strain caption = director = Mikael Salomon producer = Ridley Scott Tony Scott David W. Zucker Tom Thayer Mikael Salomon writer = Novel: Michael Crichton Screenplay: Robert Schenkkan starring = Benjamin Bratt Eric … Wikipedia
Viscoplasticity — Figure 1. Elements used in one dimensional models of viscoplastic materials. Viscoplasticity is a theory in continuum mechanics that describes the rate dependent inelastic behavior of solids. Rate dependence in this context means that the… … Wikipedia
solids, mechanics of — ▪ physics Introduction science concerned with the stressing (stress), deformation (deformation and flow), and failure of solid materials and structures. What, then, is a solid? Any material, fluid or solid, can support normal forces.… … Universalium
rock — rock1 rockless, adj. rocklike, adj. /rok/, n. 1. a large mass of stone forming a hill, cliff, promontory, or the like. 2. Geol. a. mineral matter of variable composition, consolidated or unconsolidated, assembled in masses or considerable… … Universalium
Rock — /rok/, n. a male given name. * * * I In geology, a naturally occurring and coherent aggregate of minerals. The three major classes of rock igneous, sedimentary, and metamorphic are based on the processes that formed them. These three classes are… … Universalium
Viscoelasticity — is the property of materials that exhibit both viscous and elastic characteristics when undergoing deformation. Viscous materials, like honey, resist shear flow and strain linearly with time when a stress is applied. Elastic materials strain… … Wikipedia
Yield (engineering) — The yield strength or yield point of a material is defined in engineering and materials science as the stress at which a material begins to deform plastically. Prior to the yield point the material will deform elastically and will return to its… … Wikipedia
metallurgy — metallurgic, metallurgical, adj. metallurgically, adv. metallurgist /met l err jist/ or, esp. Brit., /meuh tal euhr jist/, n. /met l err jee/ or, esp. Brit., /meuh tal euhr jee/, n. 1. the technique or science of working or heating metals so as… … Universalium
Non-Newtonian fluid — Continuum mechanics … Wikipedia
Earth Sciences — ▪ 2009 Introduction Geology and Geochemistry The theme of the 33rd International Geological Congress, which was held in Norway in August 2008, was “Earth System Science: Foundation for Sustainable Development.” It was attended by nearly… … Universalium